Mossberg Pre-Fit Barrels
If you are gun-savy and have a barrel vise, a Savage-format or factory Mossberg barrel nut, appropriate barrel nut wrench and the corresponding chambers’ Go and No-Go Gauges, you have everything you need to correctly install a barrel for your Mossberg action.
*Available in either 1.058"x20TPI (Standard Action) or 7/8"x28TPI (Small/Mini Action). Some older Mossberg bolt-actions use a less common 1.000"x20TPI, which none of our barrels will fit, so if you are not sure what you have, measure!
Please check our Frequently Asked Questions for our current lead times.
To be used with recoil lugs .300 or thinner.
For Standard Action Sizes, 1-1/16"x20TPI Barrel nut is required, not included.
For Small (mini) Action Sizes, a 7/8"x28TPI Barrel nut is required, not included.
Need a Standard Action Mossberg barrel nut? Head here!
Need a Muzzle Thread Protector? Head here!
(Our barrel nuts will not work with factory barrels with a semi-shoulder in place, but a like-sized Mossberg factory barrel nut will work with our Pre-Fit barrel with a slight forward gap between the nut and barrel shank)
No Shipping outside the US
*Please refer to the footer of this page for up-to-date production lead-time estimates.
Fluting: Adds 1 week to order lead time
Our Prefit 1MOA accuracy guarantee is 3 rounds at 100 yards with quality ammo and a skilled shooter. Like anything X-Caliber makes, we stand behind it 100%. If you do not think your barrel can shoot 1MOA groups or less, we will have you ship it back. We will inspect the barrel. If the barrel fails, we will build you another barrel and ship it to you at no cost. If the barrel passes all tests, it will be shipped back to you at your expense.
For more information about our 1MOA accuracy guarantee and the conditions that apply, please refer to our FAQ or Conditions Pages.
For more information on available contours, please visit our Contours page.
***************************
X-Caliber Barrel Break-In
Procedure Guide
When breaking in your new X-Caliber Barrel, you should perform appropriate fire and clean cycles to normalize the bore surface. Each fire and clean cycle consists of a certain number of rounds fired (one to five) followed by a cleaning procedure (see below for reference), to be completed a certain number of times (1-25). These vary depending on the type of steel of the barrel, bore/groove diameter, velocity and pressure of any given round, etc. This is to be used as a guide. Since our barrels are hand-lapped, each barrel may break in a little differently. Some barrels may require more or less shots or cycles to break in than what is listed here.
416R Stainless Steel: Fire One Round then Clean: Do this 5-10 times. Fire Three Times then Clean: Do this 1 time. Fire Five Times then Clean: Do this 1 time.
4140 Chrome Moly: Fire Once Round then Clean: Do this 5-25 times. Fire Three Times then Clean: Do this 2 times. Fire Five Times then Clean: Do this 1 time.
Example: For a 416R Stainless Steel barrel, you would fire one round, then perform the cleaning steps outlined below a total of five to ten times (shoot 1 round & clean, done 5-10 times) before starting the three shot cycle where you would fire three rounds and then clean as outlined below, then proceed to fire five rounds then clean, completing the break-in procedure.
Each Firing Cycle (1 shot, 3 shot or 5 shot) should be followed by cleaning the bore (see steps below for reference):
1.) Using a one-piece, coated cleaning rod with a properly sized bore brush (wet with your favorite non-foaming bore solvent), carefully clean the bore from the chamber end toward the muzzle (3-5 passes is usually sufficient). If you cannot clean from the chamber end, be sure to use a bore-guide so as not to damage the crown or muzzle end of the rifling. Let sit 30-60 seconds before moving on to the next step.
2.) Push a dry patch down the bore. (2-3 times)
3.) Put a few of drops of oil on a patch and push that down the bore so as to leave a thin film of oil inside the bore.
4.) Begin a new cycle: Fire your next round or rounds in your next firing cycle and repeat cleaning as necessary.
It is recommended to keep a written tally of your current step within the process so if you get distracted you will know where you left off.